Layers and cut settings
Colour is the layer
Every object belongs to a layer, and every layer has a colour from the palette at the bottom (00–29, plus the tool layers T1 and T2). Click a colour in the palette to put the selection on that layer.
The layer holds all laser settings. Objects, including images, never carry their own speed or power: to laser something differently, put it on another layer. That way a layer is one operation of the job, and the same settings apply to everything on it.
The Cuts / Layers window lists the layers that are in use, with mode, speed, power, air assist and output. Values can be edited right in the table; drag rows to change the order in which the layers are lasered.
Modes
| Mode | What happens |
|---|---|
| Line | The laser follows the outlines: cutting and scoring. |
| Fill | Closed shapes are engraved line by line (or in rings with offset fill). Open lines are skipped. |
Images can sit on any layer. The table then shows “+ Image”, and the layer dialog gets an Image section with line interval and image settings. Each image keeps its own image mode (see Images and tracing); speed and power come from the layer.
Tool layers T1 and T2
T1 and T2 are never lasered. Use them for construction lines, the outline of a workpiece, camera images to trace, or the path of a text on a path you do not want to cut.
Output and visibility
- Output decides whether a layer is lasered at all. Hidden layers and objects are still lasered if their output is on; KizamuBeam warns you about that before the job.
- In the Objects window single objects can be set to Don’t laser: they stay visible (faded) but are not lasered, not written to G-code and not checked.
Cut settings
Double-click a layer to open its Cut Settings. Which fields appear depends on the mode.
Common to all modes
| Setting | Meaning |
|---|---|
| Speed (mm/min) | Feed rate while the laser is on. |
| Max Power (%) / Min Power (%) | The layer’s power. Min Power is used where power is lowered: in power ramps and for the lightest tones of grayscale images. |
| Passes | How often the layer is repeated. |
| Air Assist | Switches air assist (M8 or M7) on for this layer. |
| Z offset (mm) and Deeper per pass (mm) | Only with a motorized Z axis: move the focus relative to the start height, and go deeper with each pass. |
| Material | Links the layer to an entry of the material library; also used by the 3D view and the fit calibration. |
Line
| Setting | Meaning |
|---|---|
| Kerf Offset (mm) | Moves the cut outward on outer contours and inward on holes, so parts keep their nominal size. Usually half the kerf width. |
| Tabs | Leaves small bridges uncut so parts do not fall out: count per shape or spacing, tab size, optionally skip inner shapes. |
| Perforation | Cuts a given length, then leaves a gap, for tear-off edges or fold lines. |
| Lead-in / Lead-out | A straight line at an angle or an arc into and out of the contour, always on the waste side, so the start point leaves no mark on the part. |
| Overcut (mm) | Continues past the start point to make sure the contour is closed. |
| Power ramp | Lowers the power toward corners (from a set change of direction) to avoid burn marks, optionally at the start and end of each cut too. |
| Duplicate lines | Removes lines that lie on top of each other before cutting, so nothing is cut twice. |
Fill
| Setting | Meaning |
|---|---|
| Line interval (mm) or Lines per inch | Distance between the fill lines. |
| Scan angle (°) | Direction of the lines: 0° horizontal, 90° vertical. |
| Crosshatch | A second pass rotated by 90°. |
| Bi-directional | Lasers in both directions (faster). |
| Overscan (%) | Runs past the edges with the laser off, so the head is at full speed when it fires. Avoids darker edges. |
| Fill style | Line by line, or Offset fill: rings that follow the outline inward. |
Defaults resets the fields to the defaults of the selected mode.
Sub-layers
+ Sub-layer adds further operations on the same shapes, each with its own mode, speed, power, passes and settings. A classic use is “fill, then cut the outline” on a single layer. Sub-layers run after the layer itself and can be switched off one by one.
Appearance in 3D
Appearance in 3D sets how the layer’s parts look in the 3D view: 21 materials from plywood to slate, acrylic and anodized aluminium, each with an optional own colour.
Material library
The Material window stores proven settings per material and thickness and applies them to a layer with one click. See Materials and tests.